- Home
- Forums
- Technical Troubleshooting
- MCP1F2A25LUV
Unicarriers (& Nissan) MCP1F2A25LUV:
code e-44
code e-44 on dash states atm pressure fault
where is this sampled ?? where do I start can not find any reference in manual ---this is the only code it clears for about 10 min then returns
Showing items 1 - 15 of 21 results.
What does the ni22365-ey0013 pressure sensor actually read if it's mounted on the distributor. Crank case pressure?
- Posted 20 Oct 2023 04:30
- Reply by Fritzthecat
- Connecticut, United States
Be nice to forky
Post a Reply Report this post
located part #22365EY00B ---sensor boost
monitor in dash ATM signal
it is there see above
- Posted 12 Feb 2015 05:59
- Reply by Kaplift
- Ontario, Canada
OMG who sold you this ?
Post a Reply Report this post
found an updated DTC code list for nissan systems
it says E-44 is MAP sensor error.
you may want to check that
- Posted 12 Feb 2015 04:43
- Reply by swoop223
- North Carolina, United States
You've been swooped!
swoop223@gmail.com
Post a Reply Report this post
How old is this unit?
- Posted 11 Feb 2015 23:49
- Reply by RCAV8TOR
- Alabama, United States
Post a Reply Report this post
This is our final conclusion.....Somebody replaced the harness for sure..I also checked 10 units in my back yard and all of them have the connector..Anyway, I delivered the truck with code, as it is working perfect. Lets see if client start complaining.....I hope not.....Thanks a lot..
- Posted 11 Feb 2015 06:25
- Reply by gabriel_g
- Florida, United States
Post a Reply Report this post
Sorry Gabriel I checked and all my units have the harness connection right beside dist placement (old)
Is it possible someone changed harness before you were called in ?
- Posted 11 Feb 2015 06:07
- Reply by Kaplift
- Ontario, Canada
OMG who sold you this ?
Post a Reply Report this post
Guys:
i just got the same E-44 error. When I inspected my harness, I realized my sensor is there, but harness DOES NOT have any plug connected or even available to connected. Any head up??? Where the plug can be???
- Posted 4 Feb 2015 06:55
- Reply by gabriel_g
- Florida, United States
Post a Reply Report this post
located part #22365EY00B ---sensor boost
the parts manual lists as oil pressure sensor but unicarriers lists it as a sensor
replaced part// cleared code
- Posted 13 May 2014 05:55
- Reply by Kaplift
- Ontario, Canada
OMG who sold you this ?
thanks for the help hope I can return the favor sometime
- Posted 10 Apr 2014 11:49
- Reply by Kaplift
- Ontario, Canada
OMG who sold you this ?
Post a Reply Report this post
Post your e-do addy in your profile and you might receive. Better yet tell you Nissan dealer to look in parts catalog under engine electrical then distributor. Trust me, its there.
- Posted 10 Apr 2014 11:05
- Modified 10 Apr 2014 11:40 by poster
- Reply by RCAV8TOR
- Alabama, United States
What i used to do all day now takes me all day to do.
Post a Reply Report this post
I don't suppose any of you dealer guys can find a part number for the sensor my dealer sent me a one wire oil pressure sensor and even after seeing the picture can not identify the sensor
- Posted 10 Apr 2014 07:23
- Reply by Kaplift
- Ontario, Canada
OMG who sold you this ?
Post a Reply Report this post
I used key on with engine off to locate it
just pull up the monitor screen and scroll down to #22 I think
(ATM pressure) and unplug it. it will go to 0 mv and then plug it back in try it no one was more shocked than I was
- Posted 8 Apr 2014 11:18
- Reply by Kaplift
- Ontario, Canada
OMG who sold you this ?
Post a Reply Report this post
Thats a new one on me as i have many of these units to keep up. If it is what you are describing then it is a pressure sensor for? As i don't think it is for ATM (auto trans) but i will remove one to see if it possibly linked to engine oil pressure. I am betting more on a barometric sensor if anything. Seen it but never questioned it as i have never had to fool with it. Thanks for the info!
- Posted 8 Apr 2014 07:48
- Reply by RCAV8TOR
- Alabama, United States
What i used to do all day now takes me all day to do.
Post a Reply Report this post
located atm sensor beside old distributor cap cover in block
(unit k21/25 has coil over now )
test #22 in monitor of the dash shows atm pressure in Mv
disconnect switch and volts go 0 connect and see sensor working on dash now I know what and where it is let's see if the dealer can order it I used the sister truck to locate thanks for all the reply's
Kaplift
- Posted 8 Apr 2014 05:09
- Reply by Kaplift
- Ontario, Canada
OMG who sold you this ?
Post a Reply Report this post
after doing some research on nissan obdI systems which i think this truck has? it refers to an O2 sensor fault
could be wrong though, everywhere i looked in cat's nissan based codes it stops at DTC-41
- Posted 7 Apr 2014 12:04
- Reply by swoop223
- North Carolina, United States
You've been swooped!
swoop223@gmail.com
Post a Reply Report this post
Having trouble using the Discussion Forums? Contact us for help.
Forkliftaction.com accepts no responsibility for forum content and requires forum participants to adhere to the rules. Click here for more information.
Entries open for LEEA Awards 2024 Cambridgeshire, United Kingdom
Read story
Yangshan Port named world’s best Geneva, Switzerland
Read story
Upcoming industry events …
July 10-11, 2024 - Riyadh, Saudi Arabia
INTRA-LOG EXPO SOUTH AMÉRICA 2024
September 3-5, 2024 - SÃO PAULO, Brazil
32nd Intermodal Africa 2023 Exhibition and Conference
November 26-28, 2023 - Kololi, Gambia, The
More Events
Latest job alerts …
CNC Machinist Setup
Philadelphia, Mississippi, United States
Payroll Administrator
Peoria, IL, United States
Shop Technician
Atlanta, United States
Road Technician - Telemetry Specialist LAE
Danville, IL, United States
View more jobs alerts
Movers & Shakers
Juha Pankakoski
Juha Pankakoski
Executive Vice President, Port Solutions, Konecranes
Edward Auriemma
Chief Executive Officer, Business Unit Software, Körber
Ian Cooke
Director of Academy, Lifting Equipment Engineers Association
Anthony Nash
Vice President of Manufacturing, Clark Material Handling
edition #1184 - 20 June 2024
One of the biggest forklift manufacturers in the world, Crown Equipment Corporation, has been crippled by a malicious cyber attack... Continue reading
Terminate Manual Pallet Trucks with the T20i: the 2-in-1 Smart Pallet Truck from Microlift
UN Forklift at The Industrial Network 2024 (Indonesia)
Increase pallet handling sustainability with the MEYER 4/2 Multi-pallet handler
PREMIUM business
Innovative high-quality wheels and castors for the forklift industry.
RAEDER-VOGEL
- Contact
- |
- Website
Movers & Shakers
Juha Pankakoski
Juha Pankakoski
Executive Vice President, Port Solutions, Konecranes
Edward Auriemma
Chief Executive Officer, Business Unit Software, Körber
Ian Cooke
Director of Academy, Lifting Equipment Engineers Association
Anthony Nash
Vice President of Manufacturing, Clark Material Handling
PREMIUM business
Part of Toyota Industries Group - Leading manufacturer of High-quality machines.
Tailift Material Handling USA Inc
- Contact
- |
- Website
From the forum discussions …
"Toyota post, still working after 12 years...Cheers, this was super helpful. I would never thought to check the grounding of the igniter."
Fezzman, Australia
Machinery-onQ
Machinery-onQ.com is the one place to source and sell all your new and used machinery.